🌊 Ocean Hopper Evolution Project

From 1950s Regenerative Receiver to Modern 100W SDR Transceiver

Amateur Extra Class • 100W • DC-6GHz

🎯 Philosophy: Staying True to Regenerative Roots

This implementation replaces tubes with discrete transistors while maintaining the regenerative detection principle. We use modern RF transistors (BFR93A, 2N5109) to achieve the same elegant simplicity with better frequency range and lower power consumption.

Discrete Transistor Regenerative Transceiver
ANT TX/RX PIN Diode Switch Preselector Tuned BPF Q=50-100 Regen Detector BFR93A JFET L: 10-turns T50-6 Tickler: 3-turns fmax: 500MHz Audio Pre 2N3904 Gain: 40dB Audio PA TDA2003 10W @ 8Ω Speaker Mic Mic Pre BC547 +60dB Regen Oscillator BFR93A (same!) Modulation input TX Mode Driver 2N5109 +20dB, 1W RF PA LDMOS Array 4x MRF6V2010N 100W PEP 50-512MHz LPF Bank Harmonic Filter Regen Ctrl Varactor tune Freq Control Varicap tuning Power Supply ±15V Rails +48V for PA RECEIVER PATH TRANSMITTER PATH 50Ω Impedance ⚡ Same circuit operates as detector (RX) or oscillator (TX)!

Frequency Coverage

1.8-512 MHz

160m through 70cm bands (switchable coils)

TX Power Output

100W PEP

LDMOS push-pull array with forced-air cooling

RX Sensitivity

0.15 µV

For 10dB S+N/N @ 14MHz (CW mode)

Selectivity

Variable

500Hz-6kHz (regeneration control)

Power Consumption

2W RX

180W TX (100W RF + 80W dissipation)

Component Count

~85 parts

Discrete transistors, no ICs

📦 Bill of Materials - Discrete Implementation

Component Part Number Quantity Purpose Est. Cost
RF Transistor BFR93A (NPN, fT=5GHz) 2 Regenerative det/osc $2.50
Driver Transistor 2N5109 (NPN, 1W) 1 RF driver stage $1.80
LDMOS PA MRF6V2010N (10W ea) 4 100W final amplifier $80.00
Audio Preamp 2N3904 (NPN) 2 Mic & audio stages $0.40
Audio PA IC TDA2003 (10W) 1 Speaker driver $2.50
PIN Diode Switch SMP1345 (high isolation) 2 TX/RX switching $6.00
Varactor Diodes BB909 (tuning range 1:10) 4 Electronic tuning $8.00
Toroids (HF) T50-6 (yellow, iron) 12 Coils for 1.8-30MHz $18.00
Toroids (VHF) T37-10 (ceramic) 8 Coils for 50-512MHz $12.00
Variable Caps Trimmer capacitors 6 Manual band setting $12.00
Passives Resistors, caps, inductors ~60 Support components $25.00
TOTAL ESTIMATED COST ~$170

🔑 Key Insights: Discrete Design

  • Regenerative Elegance: The same BFR93A circuit acts as detector (RX) or oscillator (TX) - just like the original Ocean Hopper's 12AT6!
  • Frequency Limits: Discrete approach works well to ~500MHz. Above this, parasitic capacitances and lead inductances become problematic.
  • Coil Design: Bifilar windings on T50-6 toroids replace the original's 3" air-wound coils. Main: 10T, Tickler: 3T.
  • Power Scaling: LDMOS devices allow 100W with proper thermal management. Each MRF6V2010N: 10W, combined to 40W, then doubled with push-pull.
  • Educational Value: This design teaches fundamental RF principles without abstraction of ICs.

🎯 Philosophy: Integrated Efficiency

Leverage modern RF ICs (SA602, NE602, AD9850) to achieve better performance with fewer components. Maintain modularity for educational understanding while improving frequency stability and reducing size.

IC-Based Superheterodyne Transceiver
ANT TX/RX RF Relay 50Ω RF Preamp MAR-6+ +20dB, NF=2dB BPF Bank Switched 8-pole Mixer SA602A Gilbert Cell DC-500MHz LO (DDS) AD9850 0.1Hz resolution IF Filter Crystal 9MHz, BW=2.4kHz 8-pole ladder IF Amp MC1350 AGC Prod Det NE612 SSB/CW BFO 9MHz ±1.5kHz Audio LM386 8Ω Mic + Pre MAX4466 Low noise Mic Speech Proc Compressor SSM2167 Bal Mod SA602A SSB Gen 9MHz IF Carrier Osc 9MHz Crystal SSB Filter Crystal 2.4kHz BW TX Mixer SA602A Upconvert to final freq TX Driver ERA-5+ MMIC +20dB RF PA Module RA100H1317M Mitsubishi 100W PEP LPF Bank Switched 7-pole Controller STM32F4 168MHz ARM + TFT Display SPI/I2C Control Bus SUPERHETERODYNE RECEIVER SSB/CW TRANSMITTER IF = 9MHz

Architecture

Superhet

Single conversion, 9MHz IF, DDS LO

Frequency Range

1.8-54 MHz

160m-6m bands with DDS tuning

Modes

AM/SSB/CW

Software-switchable demodulation

Frequency Stability

±1 Hz

DDS with TCXO reference

Sensitivity (SSB)

0.25 µV

For 10dB S+N/N @ 14MHz

Component Count

~45 ICs

+ passives, much simpler

📦 Bill of Materials - IC Implementation

Component Part Number Quantity Purpose Est. Cost
DDS Synthesizer AD9850 (125 MSPS) 1 Local oscillator $12.00
Mixer IC SA602A (Gilbert cell) 4 RX/TX mixing stages $24.00
IF Amplifier MC1350P (AGC) 1 IF gain control $3.50
RF Preamp MAR-6+ MMIC 1 Low-noise amp $8.00
RF Driver ERA-5+ MMIC 1 TX drive $9.00
PA Module RA100H1317M (Mitsubishi) 1 100W HF amplifier $180.00
Microcontroller STM32F407 (168MHz) 1 Control + DSP $12.00
Audio Codec WM8731 (24-bit) 1 Audio I/O $6.50
TFT Display 3.5" 480x320 SPI 1 Spectrum + controls $25.00
Crystal Filters 9MHz ladder (8-pole) 2 IF selectivity $60.00
Speech Processor SSM2167 (auto gain) 1 TX audio $4.50
Passives & Misc Caps, resistors, relays ~80 Support components $45.00
TOTAL ESTIMATED COST ~$390

🔑 Key Insights: IC-Based Design

  • Superheterodyne Advantage: Fixed IF allows excellent selectivity with crystal filters. No regeneration drift!
  • DDS Magic: AD9850 provides 0.1Hz tuning resolution with absolute frequency stability. Replaces VFO + PLL.
  • Gilbert Cell Mixers: SA602A combines mixer + oscillator in one IC. Low distortion, excellent isolation.
  • PA Module: Integrated LDMOS module simplifies 100W output. Built-in protection, matching, and thermal management.
  • Digital Control: STM32F4 handles: DDS programming, filter switching, AGC, display, CAT interface, spectrum analysis.
  • Frequency Limit: This architecture works well to 70MHz. Above this, image rejection becomes challenging without dual conversion.

🎯 Philosophy: Best of Both Worlds

Analog front-end for performance, digital backend for flexibility. Use high-performance ADC/DAC for I/Q processing in software. Maintains RF expertise while adding DSP power for advanced modes and filtering.

SDR Hybrid Transceiver - Analog RF + Digital IF
🚧 SDR Hybrid Architecture 🚧 Analog Front-End → ADC → FPGA/DSP → DAC → Analog Back-End Interactive schematic continues below...

💡 Coming in Phase 3: SDR Hybrid Features

  • Direct Sampling ADC: LTC2208 (16-bit, 130MSPS) samples entire HF spectrum
  • FPGA Processing: Cyclone V performs DDC, filtering, demodulation
  • Software Modes: All modulation schemes in firmware - easy updates!
  • Spectrum Analyzer: Real-time FFT display of entire band
  • Adaptive Filtering: Notch, peak, noise reduction in DSP

🎯 Philosophy: Software-Defined Everything

Minimize analog hardware. ADC/DAC as close to antenna as possible. All processing, filtering, modulation in software. Maximum flexibility and upgradeability.

Full SDR Transceiver - Maximum Software Definition
🌐 Full SDR Architecture 🌐 Direct Sampling → High-Speed ADC/DAC → FPGA + ARM → Ethernet/USB Interactive schematic continues below...

📊 Evolution Comparison Matrix

Parameter Phase 1: Discrete Phase 2: IC-Based Phase 3: SDR Hybrid Phase 4: Full SDR
Architecture Regenerative Superhet (9MHz IF) Direct sampling + DDC Direct sampling SDR
Frequency Range 1.8-512 MHz 1.8-54 MHz DC-2.4 GHz DC-6 GHz
Component Count ~85 parts ~45 ICs + 80 passives ~25 major ICs ~15 major ICs
Estimated Cost $170 $390 $650 $1200
Educational Value ⭐⭐⭐⭐⭐ (shows fundamentals) ⭐⭐⭐⭐ (classic design) ⭐⭐⭐ (hybrid learning) ⭐⭐ (abstracted)
Modes Supported AM, CW AM, SSB, CW All analog + PSK31, RTTY All modes (software)
Freq Stability ±50 Hz (varactor drift) ±1 Hz (DDS + TCXO) ±0.1 Hz (GPS-disciplined) ±0.01 Hz (atomic ref)
Selectivity Variable 500Hz-6kHz Fixed 2.4kHz (crystal) Any BW in DSP Any BW in software
TX Power 100W (discrete LDMOS) 100W (PA module) 100W (GaN module) 100W (class-D + GaN)
Power Consumption 2W RX / 180W TX 3W RX / 160W TX 8W RX / 150W TX 12W RX / 140W TX
Build Complexity Moderate (careful alignment) Moderate (SMD soldering) High (FPGA, BGA) Very High (dense SMD)
Upgradeability Limited (hardware mods) Some (firmware) High (FPGA + firmware) Maximum (software)
Spirit of Original ⭐⭐⭐⭐⭐ (TRUE regenerative) ⭐⭐⭐⭐ (classic amateur) ⭐⭐⭐ (modern amateur) ⭐⭐ (professional)

Performance vs. Complexity Trade-off

🎓 Recommendation: Progressive Build Strategy

Start with Phase 1 (Discrete Transistor) to truly understand regenerative principles and RF fundamentals. This honors the Ocean Hopper's elegant simplicity.

Evolve to Phase 2 (IC-Based) to learn superheterodyne architecture and experience professional-grade performance.

Experiment with Phase 3 (SDR Hybrid) to bridge analog expertise with digital flexibility.

Master Phase 4 (Full SDR) for cutting-edge capabilities and software-defined everything.

Each phase builds on the previous, creating a complete educational journey from 1950s vacuum tubes to 2025 SDR technology!